CSLB C6 – Cabinet, Millwork & Finish Carpentry Practice Test

These questions are part of the practice quiz. Start practicing

• Relative humidity depends mostly on location/region and ________.
• Head height on a staircase is measured from which reference to the ceiling?
• When finishing millwork and cabinetry that will be finished and coated onsite, why is it common to store the millwork in the shop rather than onsite?
• Glue that is commonly used for laminates is?
• Moisture content is equal to ____% of the equilibrium moisture content.
• Coped and mortised, coped and nailed, and half-lapped are all ways to describe:
• Cross-sanding in non-utility grade installations is allowed only for which stock shape?
• Crown molding should be:
• When cabinets are installed in adverse circumstances and are affected by overly high humidity, who is responsible?
• For circular handrails, the diameter may not be less than what inch and may not be more than what inch in diameter?
• Type A soil requires that for every 1 foot of depth (V) the trench must be excavated back ___ of a foot (H).
• Fall protection is required for bridges or walkways across excavations at a depth of how many feet?
• In underground service marking, what does RED stake indicate?
• What veneers can be cut from the burl, crotch or stump of the tree?
• All wood products are affected to some degree by humidity. In some cases this will not be adequate if which condition is present?
• What kind of plans are shop plans?
• Lengths of countertop should be:
• Which adhesive is not well suited to high oil content or non-porous surfaces?
• Among the listed ladders, which has the highest rated load capacity?
• Polish, oils and waxes are recommended for:
• When are particle based moldings acceptable?
• Flammable or combustible liquids and gases are classified as which fire class?
• Which item is commonly included in general notes for shop drawings?
• Who is responsible to inspect previously completed work and accept prior to starting an installation?
• On an extension ladder, a worker can never stand on the top ______ rung(s).
• Hearing protection is required if employees are exposed to ___ dB for ___ hours or more.
• What is a likely effect on plywood when it is left in direct sunlight?
• Which veneers can have interesting grain patterns achieved by cutting for special effect?
• In HDLP, which layer is responsible for bonding to the substrate?
• What is the minimum head clearance above stair treads?
• What do ORANGE stakes and markings indicate?
• In deconstructing kitchen cabinets, which sequence correctly lists upper cabinets before lower cabinets?
• The recommended minimum width of a landing area next to a sink is:
• What line shows hidden objects or edges and may also be used to show objects vertically placed such as shelves over a counter?
• Safety nets must be provided when workplaces are more than how many feet above ground or other unstable surfaces?
• What is the area in square inches of a floor measuring 280 inches by 360 inches?
• When gluing with basic yellow carpenters glue. How long should clamps be left in place?
• When making final delivery of a set of cabinets, what else should be delivered apart from the casework and millwork?
• For non-utility grade installations, cross-sanding is:
• Normally finger-jointed material is allowed:
• What are the two basic types of sheet products?
• Which hinge is used with full insert cabinet doors where the door fits completely into the opening and sits flush with the cabinet surface?
• Birch, alder, beech, and cherry belong to which wood category?
• For electrical hazards, safety-toe shoes must be nonconductive and should be able to prevent the wearer from completing an electrical circuit to ground. These shoes must be able to protect against how many volts in dry conditions?
• Swag or swage hinges are designed to do what in relation to space when the door is closed?
• Section and elevation symbols are used to connect one part of a drawing to what?
• Which hinge is listed as one of the three most common hinges used in cabinetry?
• Which laminate type is typically used for high-wear countertops and work surfaces?
• Which glass type is allowed within 24 inches of a door?
• What is the minimum clearance space between wall and handrail?
• When cabinets are staged at a jobsite before installation, which requirements must be met to be safe according to Architectural Woodwork Standards?
• During an excavation project, when should a shoring system be designed by a registered engineer?
• When book matching veneers, barber pole effect is connected to:
• What laminates can either be applied at the mill using heat and high pressure or purchased separately and applied by the contractor or after construction?
• Which laminate type can resemble sprayed finishes applied at the mill in appearance?
• What is the pre-waste board footage for a board that is 1 inch thick, 4.25 inches wide, and 11 feet long?
• Normal counter height for use with a wheelchair is:
• A stringer length for a staircase with a rise of 12' and a run of 16' is the hypotenuse of a right triangle. Which option is the approximate stringer length?
• On a sash window, the stool would be above the:
• If the rise is 3 ft and the base is 4 ft, what is the hypotenuse length?
• According to common cabinet construction guidance, variations in thickness will:
• The guardrail load requirement is tested with a force applied to the top edge. How is this force positioned?
• When selecting plywood grade for a project, which factors should be included?
• Are expansion joints required for wood wall paneling?
• The maximum allowed height for a step ladder is how many feet?
• The Underground Service Alert must be contacted at least how many days before an excavation project?
• What is the area of a circle with diameter 14 feet (use pi = 3.14)?
• In most cases, the minimum inside tread depth on a curved staircase is:
• Which statement is true regarding sanding different types of wood?
• Single rabbet, double rabbet, applied stop and plowed-in stop are all terms used to describe:
• What is a title block?
• If uneven floors or walls exist, cabinet adjustments exceeding how many inches for floors and walls require consultation before proceeding?
• What does AWS stand for in architectural woodwork?
• During stair installations, where would the half-newel post be secured?
• At what depth is fall protection required for bridges or walkways across excavations and trenches?
• Sheet products can have varying degrees of resistance to humidity. This is primarily dependent on which factor?
• When a glue line fails, the most common reason is:
• Which of the following is NOT among the three most common hinges?
• Variations of more than 1/2 inch in floor level are:
• Which statement defines pitch?
• Open-coat vs closed-coat sandpaper primarily refers to:
• In a residential occupancy where the tread depth is less than 11 inches, what is the maximum nosing protrusion?
• Which veneer cut yields longer, wider cuts and can influence grain pattern?
• Easements in carpentry commonly refer to adjusting what feature?
• Chord segmentation is a technique for what purpose?
• The unit used to measure lumber volume is called what?
• In millwork terminology, an applied stop is most closely associated with which component?
• The maximum allowed height for a two-section metal ladder is how many feet?
• Classifications of scaffolds: light duty supports up to ____ pounds per square foot.
• Solid machined and block-laminated curved moldings should be:
• Which adhesive is water-soluble and can be reactivated by adding water?
• A normal working height for a kitchen counter is:
• Cal/OSHA requires two types of grounds for electrical systems. Which pair is correct?
• Which value is commonly used for pi in these calculations?
• Ordinary combustibles are classified as which fire class?
• When excavating a trench, what is the required distance for spoils piles from edge of the excavation or trench?
• Fillet is a word used in a variety of circumstances, but usually indicates:
• Which hinge is typically used for hanging doors, lids, and covers and is fastened on the edge of the door?
• For non circular handrails, the minimum perimeter, the maximum perimeter, and the maximum cross-section dimension are what?
• Exposed interior fasteners on premium installations should be:
• A patio slab is 15 feet by 23 feet and 5 inches thick. How many cubic yards of concrete are needed?
• Stainless screws should be used in which situation?
• Which statement is true about AWI finish levels?
• What is the board feet in a 2 x 4 x 8' stud?
• Price per thousand board feet can be indicated as price per ______.
• If the rise is 5 ft and the base is 8 ft, what is the length of the hypotenuse?
• What line is used to show the vertical, horizontal or diagonal center axis of an object?
• Which item is included in a title block?
• In bridge construction, new nets must meet a minimum impact resistance of how many foot-pounds?
• How many square inches are in one square foot?
• What glue is made from animal hides, is water-soluble, has long open time, can be reactivated by adding water, and has a short shelve life once opened?
• At what trench depth should the shoring design be prepared by a registered engineer?
• What line indicates movement or might show an alternative position for an object?
• In remodels or upgrades, site readiness requires the area to be what?
• For very thin veneers or certain species, what may be required to prevent grain opening during bonding?
• Which is the correct maximum height for a painter's step ladder?
• Which statement about aliphatic glue is true?
• Chord segmentation is a technique used to create what feature in wood molding?
• Which two materials are most commonly used in cabinet construction?
• When evaluating plywood grade, which factor is most aligned with client standards rather than material properties?
• Solid machined and block-laminated curved moldings should be made to:
• Anchorage fasteners should have a surface bearing head of what designation?
• A scarf joint is used to:
• A scarf joint is used to:
• Which statement best describes the content listed in a title block to help locate the drawing within a set?
• What is the area of a trapezoid with parallel sides of 10 feet and 8 feet and a height of 15 feet?
• A toy cart is a:
• Which of the following is NOT one of the five basic glue types commonly used in furniture and cabinet shops?
• Medium duty ladder type II supports up to ___ lbs.
• With hand drawing plans, what must be employed consistently?
• How high does a mantel sit with a wood fire below?
• Countertops should be set to:
• What two veneers are cut from the middle of the tree?
• In face-framed cabinet construction, doors can be built in which style?
• Special duty ladder type 1AA supports up to ___ lbs.
• What glue is one-part catalyzed by airborne moisture, sands and stains well, is strong and waterproof?
• Which statement about back finishing is true for factory finished casework?
• When fastening parts and cases, which practice is recommended?
• Which adhesive is toxic while curing?
• What line shows an object with perpendicular extension lines at the corners, or indication the centers?
• Lumber thickness is described in quarters of an inch. What thickness does 8/4 indicate?
• What is the technical term for the toe kick that holds up a floor cabinet?
• A carbon dioxide fire extinguisher is used on what class of fire(s)?
• Rank the maximum heights of the listed ladder types from smallest to largest.
• What laminates are less durable and are often used for interior cabinet walls? They can be similar in appearance to some sprayed finishes applied at the mill.
• It is the responsibility of a cabinet installer to check that work site conditions meet acceptable standards. If they do not, what should be done?
• Which tool is not typically used when scribing wood?
• What line shows locations of a section or elevation?
• What lines connect notes, text or identifying label in the plan?
• Cabinet wall anchorage screws should be within how many inches of the top and bottom surfaces?
• In a residential occupancy where the tread depth is less than 11 inches, what is the minimum nosing protrusion?
• A wall is 35 feet long and uses 2 x 4 x 8' studs at 16 inches on center. How many board feet are in the vertical studs?
• What is the volume of a cylinder with diameter 8 feet and height 15 feet?
• To estimate or bid a contract prior to signing, what must be provided?
• The organization abbreviated AWI stands for which entity?
• How do you calculate the slope of the staircase?
• Head height on a staircase is measured from which reference to the ceiling?
• Which component helps prevent chatter by holding stock down on a thickness planer?
• When removing kitchen cabinets, assuming that the area has already been cleared and other impediments have been removed, in what order should the cabinets be deconstructed?
• What is the minimum number of hinges for an 84-inch high cabinet door?
• According to building code, handrails should be installed between what inches and what inches measured above the stair tread nosing or finished surface of a ramp slope?
• Birch, alder, beech, and cherry are all which category?
• Humidity control may not be adequate if the pieces have significantly different combined material densities. True or false?
• Half Newel is attached to what?
• All wood products are affected by humidity to some degree. True or false?
• What is the maximum height for a painter's step ladder?
• Which ladder category corresponds to the highest load capacity among the listed options?
• A guardrail system must withstand a force of at least how many pounds applied 2 inches on the top edge in any outward or downward direction?
• Which property must safety-toe shoes have for protection against electrical hazards?
• The installer is responsible for cutouts when:
• There are two tests OSHA requires for a competent person to verify that equipment grounding is executed properly. What are these two tests?
• In scaffold construction, a platform that is 10 feet or higher above its support must not extend beyond its support by more than how many inches?
• If chemical resistance is a requirement, which fastener material is preferred?
• Small gaps in an installation are acceptable if:
• Steam bending is a technique sometimes used in a project. However not all lumber is suitable for this process. Ignoring other concerns, which tree species is the best choice for steam bending?
• For scaffolds with platforms 10 feet or more above the ground, the overhang beyond the support must not exceed how many inches?
• To avoid blue stain in wood, which practice is recommended?
• When building oak cabinets, the trim and moldings will be from solid stock. However, A2 grade plywood will be used for the panels. Should a rotary-cut surface veneer product be used?
• The AWI finish levels describe which two aspects of cabinetry?
• With yellow carpenter glue, what is the typical cure status after 60 minutes that allows clamp removal?
• It is often recommended to wipe faces with a damp cloth before applying a urethane glue. Why?
• What is the minimum tread length on a staircase?
• The barber pole effect in veneer matching is connected to:
• What is the normal open time for yellow carpenters glue?
• Brads used in fastening do not need to be filled. Which statement is true about brads after fastening?
• Extra heavy duty ladder type 1A supports up to ___ lbs.
• What is the difference between open-coat and closed-coat sandpaper?
• A handrail may project a maximum of how many inches into the required stair width?
• What is the required thickness when using plywood in shoring systems?
• What is the area in square feet corresponding to 100,800 square inches?
• Which adhesive sands and stains well and is strong and waterproof?
• Architectural woodwork standards (AWS) are often specified on plans or contracts. If they are not:
• Which grade would you apply to all areas finished to a high level of craftsmanship and using matched materials and hardware?
• When clamping a joint after gluing, how tight is tight enough?
• When is back finishing or sealing required?
• What happens when voids exist in cabinet plies during gluing?
• Which veneer cutting method is used to achieve longer grain runs?
• When storing cabinets prior to delivery for finishing, which practice is recommended?
• What line can be seen in a 3D or plan view and is also used for dimension and leader lines?
• In Type B soil, the backfill per depth is most correctly described as which of the following ratios?
• Which statement about extension lines in dimensioning is true?
• Cratering is a term used to describe:
• In stair construction, a stringer is used to support what component?
• The statement that finish level smoothing with a router or power planer depends largely on the number of blade passes per inch, KCPI, is true.
• Lifelines anchored to an anchorage must support a minimum dead weight of how many pounds?
• Which grade would be chosen for a project requiring the highest possible finish and materials?
• Gaps between wood-to-wood flat surfaces should not exceed which value on a premium grade installation?
• What glue is a two-part catalyzed glue that is very strong, fills voids, waterproof, and toxic while curing?
• In oak cabinet construction, if A2 plywood panels are used, should rotary-cut surface veneer be selected?
• Shellac is a finish:
• Which standard is commonly used to govern architectural woodwork practices?
• How many fasteners should a cabinet or case have at minimum?
• When building a set of face framed cabinets, how are the doors built?
• Custom Grade is specified for areas with high craftsmanship and uses what type of materials and hardware?
• What is the lateral surface area (excluding top and bottom) of a cylinder with diameter 8 feet and height 15 feet?
• Which pair of woods is more likely to absorb stain unevenly?
• Which of the following tools is not used when scribing wood?
• Which hinge design refers to bending one or both leaves at the barrel to reduce the clearance and eliminate the need for a mortise?
• Anchorage fasteners must penetrate into studs and framing by at least how many inches?
• Which type of plan is described as pictorial in the material?
• Which of the following heartwood species is not recommended for exterior use?
• Architectural Woodwork Standards (AWS) are widely recognized and commonly specified because they represent what?
• Special duty scaffolds should be designed by which professional?
• The first step upon arriving at a new installation site is to check for site readiness. What does site readiness mean?
• The ladder should extend past the top level by at least how many inches?
• What kind of door closer will a left hand reverse door use?
• How many cubic feet are in one cubic yard?
• Which adhesive is commonly used for laminates?
• Choosing the most appropriate glue for a certain application is always important. Why should a urethane be used?
• Which of the following is the correct minimum number of braces used when shoring trenches?
• A certification is required for operating cranes with a rated capacity of at least how many tons?
• Closet shelves should be at least 3/4 inch thick.
• When installing a wood floor, what is the most important consideration?
• It is recommended that exterior doors should not be:
• In normal circumstances, how much is allowed to adjust the height of cabinet footings?
• Which ladder type is limited to a maximum height of 48 feet?
• Whose responsibility is it to ensure the job site is ready, base construction meets standards, and all new work is conformed to code before cabinet installation?
• What does GREEN stakes and markings indicate?
• How should anchorage fasteners be installed?
• Moisture content in wood is measured as a percentage by weight. The percentage for hardwoods is ____ and for construction lumber is ____ which is the industry average.
• In trench safety, Type B soil requires that for every 1 foot of depth (V) the trench must be excavated back ___ foot (H).
• What term describes the vertical or inclined earth surfaces formed as a result of excavation work?
• Veneer-core plywood is not recommended for which cabinet component?
• If the slope is 4/12, what is the pitch?
• Using iron wool on unfinished wood can cause which problems?
• Type C soil backfill per depth is 1.5 feet. For a trench depth of 2 feet, how many feet must be excavated back per foot of depth?
• If cabinet adjustments exceed 1/2 inch for floors or 1/4 inch for walls, who should be consulted before proceeding?
• Plywood and particleboard are the most common materials used in cabinet construction. There are many differences from one product or manufacturer to another. What is the general rule about thickness?
• What state should the glue reach before pressing surfaces together in veneer bonding?
• Before working on a circuit, what must be done?
• To achieve the best surface for staining and finishing a cabinet, which is the best choice?
• What are the main decision making factors for choosing what glue to use?
• What are the two most common types of protection from electrical hazards?
• What is the total board footage for a four-quarters board 4.25 inches wide and 11 feet long, adding 10% waste?
• In scaffold construction, each platform-end 10 feet or less should not extend beyond its support by more than how many inches?
• Which veneer cut produces grain patterns that resemble solid lumber?
• A sub-front is:
• What does it mean when the ground is marked with WHITE stakes or markings?
• What should shop drawings include?
• Blotchy finishes are usually a result of:
• Which operation converts the product to board feet in the example calculation?
• What do you need to know to determine the height of a cutting blade?
• Plate glass is permissible within what maximum distance from a door?
• Normally, joints in countertop sections should be:
• What thickness does the lumber term 4/4 indicate?
• Wood braces and diagonal shores must be at least _______.
• What type of window glass can be used within 24 inches of the door?
• Approximately how many linear feet of stair nose would you typically need for a standard installation?
• When applying medium sized sheets of surface wood veneer by hand, the basic tools are:
• When installing a door frame, the top should be straight with the header and:
• A floor area measures 280 inches by 360 inches. What is the area in square feet?
• What is the minimum size for wood braces and diagonal shores?
• In some cases, it might be unwise to use plastic wrap on new cabinets. Why?
• In a contract there may be reference to appearance grades, which applies to:
• In many cases, veneer-core plywood is a usable product for cabinets. However, there are particular areas where it is not recommended. Where?
• If employees are exposed to falls in excess of _________, they must be provided a personal fall arrest system.
• The maximum allowed height for a mason's ladder is how many feet?
• Hinges and catches should be:
• For wall-hung cabinets, who is typically responsible for wall blocking?
• When calculating board feet, which length unit is used in the expression thickness x width x length?
• For a stair tread depth under 11 inches, what is the maximum nosing protrusion?
• Edge banding will often use:
• Hinges and catches should be:
• When measuring the length of joints, use:
• What is another term for bookmatching?
• Closet ends and back cleats should be at least which cross-sectional dimension for proper support?
• What is the space between posts on a staircase?
• Which woods might tend to accept stain in an uneven manner?
• What glue is most commonly used in cabinetry, has a short working time, best used for tight joints without gaps or voids, not well suited to high oil content or non-porous surfaces, and has a cure time of 24 hours?
• Level balustrade should be:
• Why is it preferable to apply finishes before assembly?
• Shellac is a finish:
• Although lacquer is a suitable finish for case work and moldings, when should it not be used?
• Birch, alder, beech, and cherry are examples of which broad category of trees?
• Applying finishes before assembly is preferred because it yields:
• For a 35-foot wall using 16 inch on center studs, how many studs are required?
• If a cabinet door is finished on two faces and two vertical edges, how many distinct sides are finished?
• Normal counter height for use with a wheelchair is:
• If the slope is 6/12 and the run is 8 feet, what is the rise?
• Some wood species used as veneers will be prone to the grain opening up when glue is applied. How can this be mitigated?
• For steam bending, which species is most often chosen for bending work?
• Which grade is typically used for areas that are not visible under normal viewing?
• On an extension ladder, how many of the top rungs from the top are unsafe for standing?
• How long should casework and millwork be acclimatized to the jobsite prior to installation?
• In general stiles and rails should be:
• When using harnesses, lifelines and lanyards, lifelines shall be secured above the point of operation to an anchorage or structural member capable of supporting a minimum dead weight of how many pounds?
• Which part of a planer functions to hold down the stock and help prevent chatter?
• What veneer cut is taken from the upper part of the tree?
• Which statement about on-site finishing is true?
• Which laminate type is typically used for interior cabinet walls and has lower durability?
• What is the diameter of a circle with a radius of 5 feet?
• Light duty ladder type 111 supports up to ___ lbs.
• When removing an existing kitchen, how many breakers would you expect to supply the kitchen area?
• In a full insert cabinet door, how does the door fit relative to the cabinet opening?
• What is the recommended countertop height relative to drawer tops or doors, including tolerance?
• What is the maximum height for a cleat ladder?
• When should a filler be used before applying a finish coat?
• When building stairs, what is the minimum head clearance above stair treads?
• Closet shelves with an attached rail must have ends and back cleats of at least which dimensions?
• On premium grade installations, exposed interior fasteners must be:
• Where can you review symbols for floor plans?
• Which equation represents the Pythagorean relationship used to calculate the stringer length for rise and run?
• Bases or toes should be:
• What are the most common fasteners used in cabinetry and furniture?
• Before applying urethane glue, wiping faces with a damp cloth is intended to ensure which result?
• Which factor primarily influences the finish level when smoothing with a router or power planer?
• Finish specifications include which three elements?
• What is the circumference of a circle with a radius of 5 feet, using pi = 3.14?
• A properly designed scaffold must be able to support its own weight and ______ times the maximum intended working load applied or transmitted to it.
• Gluing is an important part of any joinery project. Apart from choosing the best type of glue for the project on hand, what other consideration would be most important when gluing pieces?
• According to Cal/OSHA, what type of ladder can withstand a working load of 250 pounds?
• Easements are usually parts associated with:
• What term describes matching two veneers side by side to produce a mirrored grain pattern?
• What is the decimal feet value of 5 inches when used in volume calculations?
• Architectural drawings include which item?
• When shoring trenches, how many braces must be used?
• In trench safety, shoring is required if the trench depth reaches what?
• Cabinet footings height in normal circumstances is limited to an adjustment of:
• Why is it not recommended to use iron wool on unfinished wood?
• With glues, Type I or Type II is an indication of:
• Polishing a finished wood piece with steel wool can cause contamination that leads to what?
• Which statement defines slope?
• What is the typical minimum mantel clearance above a fireplace in residential settings?
• An important rule in plywood construction is which of the following?
• Chord segmentation is:
• On ornamental woodwork, wood filler strip length should not exceed ______.
• What are the AWI's three basic levels of finish?
• How many sides are finished on a cabinet door?
• What is the area of a triangle with a base of 12 feet and a height of 12 feet?
• How do you locate studs?
• When fine sanding a completed piece, why avoid a final polishing with steel wool?
• What lines are used when space is limited and an object must be viewed separately from the main object?
• Is the overall scale required on plans?
• Using pi = 3.14, the circumference of a circle with diameter 8 feet is approximately:
• In calculating the volume of a slab with length and width in feet and thickness in feet, the resulting unit is which?
• HEPA filters can remove particles whose diameter is equal to:
• For wood wall paneling, what specification is commonly required for expansion joints per elevation?
• Which statement correctly reflects crane operation requirements based on the material?
• In a single-story home, what is the maximum spacing that framing studs can be from each other?
• OSHA requires a personal fall arrest system when exposure exceeds how many feet?
• What laminates are mostly used for countertops and work surfaces?
• What is the maximum allowed height for a three-section metal extension ladder?
• According to standards closet shelves should be:
• Type C soil requires that for every 1 foot of depth (V) the trench must be excavated back _____ feet (H).
• Safety nets must extend beyond the work surface by how many feet?
• Whose responsibility is it to provide wall blocking for wall-hung cabinets?
• Birch, alder, beech, and cherry are all:
• Generally, what is the best method to attach MFD shelves?
• When installing adjacent cabinets, attach them at the rear to available framing and at the front to:
• A line rises 4 feet over a horizontal run of 8 feet. What is its slope?
• True or False: The contractor is responsible for any blocking, backing, furring, grounds, or structural members that become part of the general construction required to complete an installation unless otherwise stated in documents.
• Which formula yields board feet when measuring length in feet and other dimensions in inches: thickness x width x length divided by 12, or thickness x width x length divided by 144?
• Which class corresponds to energized electrical equipment?
• Finishing of cabinets and millwork on site is:
• Which adhesive is commonly used for edge banding in cabinet making?
• What does a perspective sketch require?
• What glue comes in various grades determined by the degree of water resistance? The higher the water resistance often reduces the strength therefore, not making this glue suitable for humid climates.
• All extension ladders should be placed at a ___ degree angle.
• Shoring, benching or other cave-in protection system is required if the trench is ______ or deeper.
• Finger-jointed material is allowed under opaque finishes.
• Fillet is commonly used to describe a flat surface in relation to curved elements.
• The installer should handle cutouts whenever needed. Which option represents this guidance?
• Premium Grade is reserved for which scenario?
• Combustible metals fires fall under which class?
• What are acceptable tolerances when installing trim and cabinets?
• Blotchy finishes result from which condition?
• In HDLP, the top layer is the decorative layer.
• What is the result after applying a 10% waste factor to 3.9 board feet?
• For Type A soil, if the trench depth is 6 feet, how far should the trench be excavated back (H)?
• What is the minimum tread length on a staircase?
• When using epoxy glue:
• PPE is the last line of defense after what controls fail?
• Type B construction is the same as:
• Aliphatic glue is ...
• Why should you be cautious when using cabinets with voids?
• From which part of the tree are rotary and half-cut veneers produced?
• When checking gaps for compliance, which tool should you use?
• What are the most common type of plans?
• On floor plans, what does the orientation mark show?
• The recommended maximum distance from sink to dishwasher is:
• Economy grade is the minimum acceptable level of finish and workmanship, typically reserved for which areas?
• Cabinets and casework finished with transparent type finishes, should be:
• Which description matches a cabinet door finished on two faces and two vertical edges?
• The most common reason for the failure of shop applied finishes is:
• Cooking media fires are classified as which class?